Glossary termAbutment
buttress
Strebepfeiler
A pier projecting from the outside of a wall at the point where a vault thrusts, resisting the thrust by its weight and depth. Its resistance grows roughly with the square of its projection.
Names
- English
- buttress
- German
- Strebepfeiler
- French
- contrefort
Sources
Related terms
Used in
Lessons
- Lesson 1: Why arches stand
- Lesson 2: Pointed or round?
- Lesson 3: The bay
- Lesson 5: Holding back the thrust
- Lesson 6: The flying buttress
- Lesson 7: Hall church or basilica?
- Lesson 8: Ending the choir
- Lesson 9: The chevet
- Lesson 10: Rules of thumb across the centuries
- Lesson 12: Mouldings, gables and portals
- Lesson 14: The cracked buttress
- Lesson 15: The flyer’s range of thrust
- Lesson 16: Proportion: documented and disputed
- Lesson 18: Towers and spires
- Lesson 20: Reading a cathedral
- Lesson 23: Roriczer’s pinnacle
Rules that mention it
- Hoffstadt's buttress rule
- Mohrmann's rule of experience
- Historical range of wall and buttress dimensions
- Direct sizing of a prismatic buttress
- Reductions of the table values
- Required abutment dimensions (Tables 2–4)
- Line of thrust through the abutment
- Side apse on the diagonal of the last aisle bay
- Polygonal side apse and the gap beside it
- Closed ring of chapels
- Chapels with windowed bays between
- Shape and depth of the radiating chapels
- Chapel walls, arches and wall piers
- Buttresses between the chapels
- Stair in the angle beside the side apse
- Positions of tower stairs
- Tower walls
- Heights and flyers of the stepped five-aisled section
- Five-aisled churches: three systems
- The buttress receiving the flyers
- The rising coping
- The arch line of the flyer
- Head and foot of the flying buttress
- Hall church: heights, piers and buttresses
- How high the buttress must rise
- Six ways to form the upper wall
- Wall thickness by the moment equation
- Lab arch: modelling assumptions
- The cracked buttress
- Buttress against overturning: minimum depth and geometric factor
- 1890 against modern statics
- The flyer’s range of thrust
- The arch on leaning buttresses
- The leaning buttress
- Buttress caps and their cornices
- Buttress offsets
- Gutter in the cornice
- Parapet and gallery on the cornice
- Late Gothic mouldings
- Pinnacle of several stones: crown limited by the block
- Figure shrines on buttresses (Gehäuse)
- Sill course and sill (Kaffgesims, Sohlbank)
- Blind arcades and blind panels
- Wall passages before the windows
- Corner buttresses
- Buttress rule of the earlier editions
- Buttresses beside straight bays
- Buttress thickness
- Radial buttresses on the choir polygon
- Wall thickness and bay length
- Wall between buttresses
- Full wall without buttresses
- Buttresses at the west end
- Portal filling the bay between buttresses
- Projecting portal: gable wall and terrace
- Continuous splay and jamb depth
- Pinnacles beside the portal gable
- Porches between buttresses and larger porches
- Buttress depth by the modern criterion
- Target factor of a buttress, cracked
- Both verdicts on every support
- Joint factor of piers and clerestory walls
- Chain of resultants through a basilica section
- End forces of a flying buttress
- Buttress courses and set-offs
- Wall coursing: continuous beds, broken head joints
- Buttress depth from the statics
- Detail of the 3D model
- Transverse section and its load cases
- The thrust through a double span in the statics
- The flyers over doubled aisles in the statics
- Storm as a rare load
- Towers of the design
- Buttresses of the tower and their pinnacles
- Intermediate stage and corner pinnacles (TW17, TW18)
- Corner turrets on the buttresses (C5)
- Setbacks and wall reduction per storey
- Tower tops: terrace and corner turrets (TW9)
- From the square into the octagon (TW16)