Skip to content
Ungewitter

Help

Everything the site can do, in the order you will meet it. For lesson plans and assignments, see the teacher guide.

The Studio

The Studio holds one church design and shows it in every view at once. Start from the default church or pick one from the Book example list in the rail: the hall churches of Examples I and II, the basilica with flyers of Fig. 408, the Amiens and Cologne chevets, a parish church with a west tower, a late-Gothic hall after Annaberg, and the five-aisled cathedrals of Paris and Bourges.

Parameters and views

The rail on the left holds the parameters in groups: plan, vaulting, statics, elevation, tracery, towers and portals. Each slider marks the value the rule gives with a tick; move away from it and a button, Reset to rule value, brings it back. The views are tabs: Plan, Bay, Section, Elevation, Chevet, Tracery, Tower, Portal and 3D. Select a bay in the plan to draw it in the Bay tab and to cut the section through it. Drag a drawing to pan it, scroll or pinch to zoom, double-click to fit it again.

Five-aisled churches

Choose five aisles for a basilica and the elevation group offers Doubled aisles, the book’s three systems (pp. 289–290, 389–390): one flyer over both aisles, as at Paris and Ulm; two spans over an intermediate pier on the row between the aisles, the usual way, as at Cologne; or stepped heights, the inner aisle raised with its own triforium, clerestory and flyers, as at Bourges. For the double span, Head of the lower flyer either continues the upper flyer’s back (Fig. 896) or is raised so that the two thrusts meet head on (St-Ouen, Fig. 896a). Each choice names its rule; the Section view and the statics follow it. One book example shows each system: Paris, Cologneand Bourges.

Rule sets

The rule set decides how walls and buttresses are sized; switch it and the whole design is recomputed.

  • Ungewitter 1890 (Mohrmann): the rules of experience of the third edition (pp. 273–276).
  • Ungewitter 1890, statics: every buttress sized from the line of thrust, joint by joint, so that it stays in the kern.
  • Heyman, limit analysis: buttresses sized to a geometric safety factor of 2 under the permanent loads and 1 under wind, cracked.
  • Hoffstadt, Viollet-le-Duc, Hase, earlier editions, Lechler: the older rules the book reports, for comparison.

Findings and the inspector

The findings bar along the bottom lists everything the rules have to say about the design: ✕ errors (a geometric impossibility, or a line of thrust leaving the section), ▲ warnings (a rule of experience not met) and · notes (teaching remarks). Click a finding to select its element, or click any element in a drawing: the inspector shows the rule that sized it, its evidence level, the source with page and quotation, and for a buttress both verdicts, 1890 and modern.

Undo, reset and small screens

The toolbar has Undo and Redo (also on the keyboard, see below); every change, including Back to the book example, can be undone. Under the Heyman rule set the verdicts also give each vault's allowable spreading: how far its supports may move apart before it collapses. On a phone the parameters open in a drawer from the toolbar, and the tab bar scrolls sideways.

Sharing links

The whole design lives in the address, after #d=. Copy link puts it on the clipboard; whoever opens it sees exactly your design. The part after # is never sent to the server, so nothing is stored anywhere but in the link. Links from older versions of the site still open: they are migrated to the current format, and if part of a link cannot be read, the Studio says that it repaired it.

Exports

Export SVG, Export PDF and Export DXF write the current view as a drawing sheet at its plot scale, with ISO line weights. Choose the paper (or let the smallest sheet that fits be chosen) and whether cut masonry is drawn solid or hatched by material. PDF and SVG are for printing and presentations, DXF (with true arcs) for CAD. The 3D view downloads glTF and OBJ. Present shows the views one after another in full screen.

Embeds

Embed this view opens a bare, read-only page of the current view. Put its address in an iframe to show a live drawing in a course page or a slide:

<iframe src="https://ungewitter.gobbo.work/en/embed/?view=section#d=…" width="800" height="600" title="Section of my church"></iframe>

Collections

Add to collection gathers designs, for a class or to compare variants. The collection stays on this device until you copy its link, which carries every design in one address. Collections lists ready-made sets for teaching. For assignments with automatic checks, see the teacher guide.

The Tracing floor

Medieval masons drew their constructions full size on a plaster tracing floor. The Tracing floor takes one part of the building at a time. Each tool replays its construction stroke by stroke, cites the rule and page behind every step, and exports its sheets.

Open in Studio carries a tool’s settings into a Studio design; from the Studio, Open in the tool goes back with the current design. The Lab isolates a single arch on its buttresses: drag its thickness, rise and buttress, follow the line of thrust through the kern, and switch between the 1890 method and Heyman’s analysis.

The 3D view

The 3D tab of the Studio and the 3D model page build the church from the same design: walls, piers, buttresses and flyers, moulded ribs and webs, tracery, pinnacles, portals and towers.

Moving around

  • Drag to orbit; right-drag or Shift-drag to pan; scroll or pinch to zoom. Click an element to inspect it.
  • View jumps to an axonometric, the west front, the side, or the cut interior. Detail follows the zoom, or holds massing, detail or tracery.

Walk mode

Walk through puts you at eye height inside the west door. Walk with W A S D or the arrows, drag to look round, and press Escape to leave. Shift walks faster; Home brings you back to the door.

Section cuts

A section plane, longitudinal on the axis or transverse through a bay, cuts the model open; its slider moves the cut. Everything cut is filled with hatching, so walls, piers and vault shells read as solid. The section box trims the model from all six sides at once: west to east, south to north, floor to roof.

Without WebGL 2 the page shows a written description of the model instead.

Keyboard shortcuts

Studio

KeyAction
Ctrl / ⌘ + ZUndo
Ctrl / ⌘ + Shift + ZRedo
\Presentation mode
→ or Page DownNext view (presentation)
← or Page UpPrevious view (presentation)
EscLeave the presentation

3D view, when it has the focus

KeyAction
← → ↑ ↓Orbit
Shift + arrowsPan
+ · −Zoom in · out
Home or 0Reset the view
EscClear the selection

Walk mode

KeyAction
W or ↑Walk forward
S or ↓Walk back
A · DStep left · right
← · →Turn left · right
Page Up · Page DownLook up · down
ShiftWalk faster
HomeBack to the west door
EscEnd the walk

Search and glossary

KeyAction
↓ · ↑Move through the search results
EscClose a glossary popover

Offline use

The site works without a network, which helps in a classroom with poor Wi-Fi. On the first visit your browser keeps the Studio, the Lab, every Tracing floor tool, the 3D model, the assignments and the index pages; lessons, building, term, rule and source pages are kept as you read them.

To install it as an app, use your browser’s Install or Add to Home Screen command (in the address bar or the share menu). When a new version is out, a notice offers to reload; until you accept, the version you have keeps working. Search needs its index, which is kept once you have searched online.

Questions

Why does my buttress fail?

Open the Section tab and look at the line of thrust through the buttress under each load case. A triangle marks the joint where the line leaves the kern, the middle third; a cross marks a joint that fails outright. The findings and the inspector name the rule, the joint and the load case. Often it is the wind. What helps:

  • a deeper buttress (pin its depth, or let the Ungewitter 1890, statics rule set size it for you);
  • a steeper vault: a pointed arch of greater rise thrusts less than a round one;
  • lighter webs (a lighter row of Table I), or a lower springing;
  • in a basilica, flying buttresses that carry the nave thrust over the aisles.

The modern verdict may differ: Heyman’s analysis lets the line leave the kern as long as it stays inside the masonry, and asks for a geometric safety factor instead. Lesson 5 and Lesson 14 explain both.

What do the evidence levels mean?

Each rule carries a level: documented (a medieval text says so), treatise (a nineteenth-century textbook, above all the one of 1890), derived (our derivation from a construction in the sources), assumed (our default where the sources give a range or say nothing) and disputed. Each extracted number is also marked [V] checked on the scan, [T] from the OCR text, [D] derived, [M] measured off a figure or [U] uncertain. The About page explains them in full.

Can I print drawings?

Yes. Export the view as PDF and print it at 100 % (not “fit to page”): the sheet is drawn at its plot scale, so a 1 : 200 plan measures true with a scale rule. The SVG export prints the same way from any vector program. An assignment result prints without the site’s menus, as a hand-in.

How do I cite this?

Cite the site, and for a design, its link (Chicago author-date, as in our sources):

BK. 2026. Ungewitter: Gothic Construction after the Lehrbuch of 1890. Web application. https://ungewitter.gobbo.work/en/. Accessed [date].

For a design, add “Design: ” and the Studio link. Cite the book itself with its printed page:

Ungewitter, Georg Gottlob. 1890. Lehrbuch der gotischen Konstruktionen. 3rd ed., revised by Karl Mohrmann. Vol. 1. Leipzig: Weigel. In the text: (Ungewitter 1890, 275).

Our texts and drawings are CC BY 4.0: you may reuse them with this credit. See sources and licences.