Skip to content
Ungewitter

← All reference buildings

St Mary’s Church, Lübeck

Lübeck · St. Marien zu Lübeck · Marienkirche Lübeck · Wikidata Q695065

6 measured · 3 published · 8 provisional

The mother church of Baltic brick Gothic: begun as a hall about 1251 and changed to a basilica on the French cathedral plan about 1265, with the highest brick vault in the world (38.5 m). Brick is lighter and weaker than ashlar; the checks below still assume heavy stone.

Facts

Main building campaign
1251–1351 provisionalde Wikipedia, revision 272026198Gothic church begun 1251, finished with the towers in 1351.
Plan type
Basilica, 3 vessels, no transept provisionalde Wikipedia, revision 272026198Begun as a hall church, changed to basilica around 1265.
Material
brick provisionalde Wikipedia, revision 272026198'Mother church of Brick Gothic'; highest brick vault in the world.
Choir ending
5/8: 5 sides of a 8-sided polygon provisionalDehio & von Bezold, Tafel 448, Fig. 1
Towers
Twin west towers 124.95 m and 124.75 m with weathercocks (120 m to the ball); built 1304-1351. provisionalde Wikipedia, revision 272026198
Vaults
Nave: quadripartite publishedDehio & von Bezold, Tafel 448, Fig. 1The ambulatory is vaulted in triangular cells.
East end
an ambulatory with 5 radiating chapels provisionalde Wikipedia, revision 272026198de: ambulatory with a ring of chapels; the plate shows the projecting axial chapel and shallow chapels in the other bays.
Towers in plan
two west towers publishedDehio & von Bezold, Tafel 448, Fig. 1
Flying buttresses
one tier publishedDehio & von Bezold, Tafel 469, Fig. 3

Dimensions

DimensionsValueConventionSource
Nave width14.13 m ± 0.15 mNave piers, axis to axisaxis to axismeasuredDehio & von Bezold, Tafel 448, Fig. 1measured from (1130, 2194.5) to (1551, 2184) px; scale 10 m = 298 px
Other figures
Aisle widths9.98 m ± 0.15 mAisle, pier axis to inner face of the wallaxis to axismeasuredDehio & von Bezold, Tafel 448, Fig. 1measured from (832.5, 2194.5) to (1130, 2194.5) px; scale 10 m = 298 px
Bay length6.09 m ± 0.05 mNave pier axes over 4 bays (mean; the bays shrink westwards)axis to axismeasuredDehio & von Bezold, Tafel 448, Fig. 1measured from (1555, 1987.5) to (1555, 2713.5) px; scale 10 m = 298 px · over 4 bays
Nave vault height38.5 mto the crownprovisionalde Wikipedia, revision 272026198

Vault crown of central vessel 38.5 m; table after Hirsch/Schaumann/Bruns 1906, p. 125, and Hasse 1983, p. 243.

Other figures
Aisle vault heights20.5 mconvention not statedprovisionalde Wikipedia, revision 272026198

Aisle vault height 20.5 m (dimension table).

Other figures
Piers2.45 m ± 0.1 mNave pier across the shafts, transverseoverallmeasuredDehio & von Bezold, Tafel 448, Fig. 1measured from (1093.5, 2194) to (1166.5, 2194) px; scale 10 m = 298 px
Buttress depths3.36 m ± 0.1 mNave buttress, outer face to inner face of the aisle walloverallmeasuredDehio & von Bezold, Tafel 448, Fig. 1measured from (738.5, 2398) to (838.5, 2398) px; scale 10 m = 298 px
Wall thicknesses0.81 m ± 0.1 mAisle wall between the buttressesoverallmeasuredDehio & von Bezold, Tafel 448, Fig. 1measured from (811.5, 2290) to (835.5, 2290) px; scale 10 m = 298 px

The design in plan

Plan of the design made from St Mary’s Church, Lübeck: quadripartite nave vaults, an ambulatory with 5 radiating chapels.010 m
The Studio design made from the values on this page, drawn by the Studio’s own generators: cut masonry black, vault ribs dashed overhead. It is a design after the building, not a survey of it. The east end comes from the chevet generator (Ch. VI), which draws the church with one aisle on each side.

One bay in plan, to scale

Plan of one bay of St Mary’s Church, Lübeck: nave 14.13 m between pier axes, buttress depth 3.36 m; dashed outline of Amiens Cathedral for comparison.14.13 m3.36 m010 m
Drawn from the values above: nave piers, aisles, outer wall and buttresses of one bay. Buttress breadth is schematic. The dashed outline is Amiens Cathedral at the same scale.

As a design

The measured values as a Studio design: vessels, nave width, aisle and bay ratios, nave bays, choir ending and transept, the springings (measured, or the vault crown less a rise of 2:3 over the clear span), the piers and the material. The recorded facts above, each with its source, give the vault types (the nave quadripartite), the chevet, the towers and the tiers of flyers; the building’s date sets the period of its tracery and portals. Everything else keeps the Studio’s defaults.

Measured against the 1890 statics and the modern check

The design is sized twice at its typical nave bay: by the 1890 statics (the least depth of wall and buttress that keeps the line of pressure in the kern) and by the modern check (Heyman: the least depth with a geometric factor of 2). The depth measured on the plate is then checked with the same forces by both criteria, so all three columns are judged alike.

Measured against the 1890 statics and the modern check
QuantityBuilding, measuredUngewitter 1890, staticsModern check (Heyman)
Depth of wall and buttress3.36 m measured3.84 m3.84 m
Building ÷ this depth–0.870.87
Kern rule of 1890edge pressure too high (with wind from the left)kern left in the storm only (with wind from the left)kern left in the storm only (with wind from the left)
Geometric factor, cracked1.74 against 2: stands, small margin2.18 against 2: safe2.18 against 2: safe
Pier (1890 plan rule)2.45 m1.92 m–
Wall between the buttresses (1890 plan rule)0.81 m1.3 m–

Forces at the springing of the nave vault, 30.67 m above the floor.

Why they differ

  • The building is shallower than the statics asks: in the model the line of pressure leaves the kern of the measured depth. The modern check asks less: only that a line of thrust stays inside the masonry, which its geometric factor measures.
  • Weight set high on a flyer pier (pinnacles, statues, the upper stages) turns the resultant downward; the design carries none of it.
  • Brick: the design weighs the walls as brick, lighter than the stone of the tables, so the rules ask for more depth.
  • The check is drawn in one plane: one typical bay of the nave, the buttress breadth taken as a share of its depth, the wall as measured where known. Real buttresses vary along the church.

Ungewitter’s rules against this building

The rules of experience reported by Ungewitter and Mohrmann (1890, pp. 273–276) size the abutment of one vault span. Here they are applied to this building’s spans and heights and set against the buttresses measured on the plate.

In a basilica the nave vault is abutted through the flying buttresses by the whole system: aisles and outer buttress together. Ungewitter’s single-span rules were never meant for it, which is the point of the comparison.

Nave vault: span 11.68 m, springing at 30.71 m

RuleFilled inRule saysBuilding hasBuilding ÷ rule
Mohrmann, rule 5D = (0.222 · 11.68 m + 0.05 · 30.71 m) · 0.855 = 3.53 m3.53 m12.12 m3.43
HoffstadtD = 11.68 m / 10 + √2 · 11.68 m / 10 = 2.82 m2.82 m12.12 m4.3
Viollet-le-DucD = 8.11 m · (1 − cos(2 · 73.7 ° / 3)) = 2.81 m2.81 m12.12 m4.32
HaseD = 2.81 m + 0.15 m · 30.71 m / 4.5 m = 3.83 m3.83 m12.12 m3.16
Earlier editionsD = (8.11 m + 0.3 m) / cos(37.2 °) − 8.11 m = 2.44 m2.44 m12.12 m4.96

Building has: whole abutment system: aisles + buttress, from the nave pier’s face

Outer aisle vault: span 8.76 m, springing at 14.66 m

RuleFilled inRule saysBuilding hasBuilding ÷ rule
Mohrmann, rule 5D = (0.222 · 8.76 m + 0.05 · 14.66 m) · 0.893 = 2.39 m2.39 m3.36 m1.4
HoffstadtD = 8.76 m / 10 + √2 · 8.76 m / 10 = 2.11 m2.11 m3.36 m1.59
Viollet-le-DucD = 6.08 m · (1 − cos(2 · 73.7 ° / 3)) = 2.1 m2.1 m3.36 m1.6
HaseD = 2.1 m + 0.15 m · 14.66 m / 4.5 m = 2.59 m2.59 m3.36 m1.3
Earlier editionsD = (6.08 m + 0.3 m) / cos(37.3 °) − 6.08 m = 1.94 m1.94 m3.36 m1.74

Building has: the buttress, from the inner face of its wall

Assumptions

  • Vault rise 2/3 of the span (a low pointed arch); springing height = vault height − rise.
  • Heavy stone; no help from the walls between the buttresses.

The modern check: Heyman’s geometric factor

The rules above size a buttress by proportion. Here the measured buttress is checked by limit analysis against an estimate of the vault’s thrust: how much shallower could it be before it overturns, as one block and once cracked?

The buttress holds the estimated thrust, but cracked its geometric factor is only 1.22.

QuantityValue
Vault thrust per bay (estimate, Table I)42 kN
Height of the thrust (springing)30.71 m
Buttress depth (measured)3.36 m
Buttress breadth (assumed: half the depth)1.68 m
Thrust it holds: block | cracked228 | 76 kN
Minimum depth: block | cracked1.91 | 2.76 m
GSF on depth: block | cracked1.76 | 1.22
Fracture height30.71 m
1890: base joint, eccentricity ÷ kern0.55

Assumptions

  • Estimates: quadripartite vault, rise 2/3 of the span, Table I (mean H₀); ashlar 24 kN/m³; the thrust acts on the inner face at the springing; buttress breadth half its depth; the masonry above the springing (pinnacles) is ignored, which is conservative.
  • In a basilica the outer buttress takes the nave vault’s thrust through the flyers; the aisle vault is left out.
  • Cracked buttress after Ochsendorf (2002) and Ochsendorf, Hernando & Huerta (2004): a straight fracture from the toe, its height from the published equations (checked against both worked examples).

How the modern check works →

Plates

Public-domain plates of this building in Dehio and von Bezold’s atlas. Open them in the Heidelberg viewer or measure them with tools/plate-digitiser.

Sources

Every work this page cites, with the plates and article revisions it uses. The plates of Dehio and von Bezold are in the public domain; Wikipedia articles serve as pointers, each fixed to its revision.