Skip to content
Ungewitter

← All reference buildings

León Cathedral

León · Catedral de Santa María de León · Kathedrale von León · Wikidata Q175874

6 measured · 3 published · 9 provisional

The most French of the Spanish cathedrals, after Reims: a three-aisled nave of only five bays, an aisled transept and a five-aisled choir with ambulatory and chapel ring. Its walls are almost all glass, which made the structure fragile; it was largely rebuilt in the 19th century.

Facts

Main building campaign
1255–1302 provisionalde Wikipedia, revision 265731078Main campaign 1255 (or shortly before) to 1302/03, nearly done but towerless.
Plan type
Basilica, 3 vessels, with transept provisionales Wikipedia, revision 176238094Three vessels: centre 30 m, aisles 15 m high.
Material
stone provisionalen Wikipedia, revision 1376000649en: a limestone of mediocre quality.
Nave bays
5 provisionalde Wikipedia, revision 265731078Comparatively short nave of only five bays.
Choir ending
5/10: 5 sides of a 10-sided polygon publishedDehio & von Bezold, Tafel 510, Fig. 3
Towers
West towers 65 and 68 m (es, fr); de gives both as 90 m. provisionales Wikipedia, revision 176238094
Vaults
Nave: quadripartite publishedDehio & von Bezold, Tafel 510, Fig. 3
East end
an ambulatory with 5 radiating chapels publishedDehio & von Bezold, Tafel 510, Fig. 3
Towers in plan
two west towers provisionales Wikipedia, revision 176238094Two west towers flanking the aisles.
Flying buttresses
one tier provisionales Wikipedia, revision 176238094es: buttresses, flyers and pinnacles along the aisles; the number of tiers is not stated, and plate 523 shows the flyers only end-on.

Dimensions

DimensionsValueConventionSource
Nave width11.97 m ± 0.15 mNave piers, axis to axisaxis to axismeasuredDehio & von Bezold, Tafel 510, Fig. 3measured from (1347, 6130) to (1699, 6130) px; scale 10 m = 294.1 px
Aisle widths7.23 m ± 0.1 mNorth aisle, pier axis to inner face of the wallaxis to axismeasuredDehio & von Bezold, Tafel 510, Fig. 3measured from (1133.5, 6040) to (1346, 6040) px; scale 10 m = 294.1 px
Bay length6.55 m ± 0.1 mNave pier axes over 2 baysaxis to axismeasuredDehio & von Bezold, Tafel 510, Fig. 3measured from (1346, 5942.5) to (1346, 6327.5) px; scale 10 m = 294.1 px · over 2 bays
Nave vault height30 mconvention not statedprovisionales Wikipedia, revision 176238094

Central vessel 30 m high.

Other figures
Aisle vault heights15 mconvention not statedprovisionales Wikipedia, revision 176238094

Both aisles 15 m high.

Piers1.6 m ± 0.1 mNave pier across the shafts, transverseoverallmeasuredDehio & von Bezold, Tafel 510, Fig. 3measured from (1323.5, 6130) to (1370.5, 6130) px; scale 10 m = 294.1 px
Buttress depths3.03 m ± 0.1 mNave buttress (north), outer face to inner face of the aisle walloverallmeasuredDehio & von Bezold, Tafel 510, Fig. 3measured from (1044.5, 6136) to (1133.5, 6136) px; scale 10 m = 294.1 px
Wall thicknesses1.43 m ± 0.1 mNorth aisle wall between the buttressesoverallmeasuredDehio & von Bezold, Tafel 510, Fig. 3measured from (1091.5, 6040) to (1133.5, 6040) px; scale 10 m = 294.1 px

The design in plan

Plan of the design made from León Cathedral: quadripartite nave vaults, an ambulatory with 5 radiating chapels.010 m
The Studio design made from the values on this page, drawn by the Studio’s own generators: cut masonry black, vault ribs dashed overhead. It is a design after the building, not a survey of it. The east end comes from the chevet generator (Ch. VI), which draws the church with one aisle on each side.

One bay in plan, to scale

Plan of one bay of León Cathedral: nave 11.97 m between pier axes, buttress depth 3.03 m; dashed outline of Amiens Cathedral for comparison.11.97 m3.03 m010 m
Drawn from the values above: nave piers, aisles, outer wall and buttresses of one bay. Buttress breadth is schematic. The dashed outline is Amiens Cathedral at the same scale.

As a design

The measured values as a Studio design: vessels, nave width, aisle and bay ratios, nave bays, choir ending and transept, the springings (measured, or the vault crown less a rise of 2:3 over the clear span), the piers and the material. The recorded facts above, each with its source, give the vault types (the nave quadripartite), the chevet, the towers and the tiers of flyers; the building’s date sets the period of its tracery and portals. Everything else keeps the Studio’s defaults.

Measured against the 1890 statics and the modern check

The design is sized twice at its typical nave bay: by the 1890 statics (the least depth of wall and buttress that keeps the line of pressure in the kern) and by the modern check (Heyman: the least depth with a geometric factor of 2). The depth measured on the plate is then checked with the same forces by both criteria, so all three columns are judged alike.

Measured against the 1890 statics and the modern check
QuantityBuilding, measuredUngewitter 1890, staticsModern check (Heyman)
Depth of wall and buttress3.03 m measured2.59 m2.67 m
Building ÷ this depth–1.171.14
Kern rule of 1890kern left in the storm only (with wind from the left)kern left in the storm only (with wind from the left)kern left in the storm only (with wind from the left)
Geometric factor, cracked1.19 against 1: safe0.97 against 1: fails1 against 1: safe
Pier (1890 plan rule)1.6 m1.63 m–
Wall between the buttresses (1890 plan rule)1.43 m1.15 m–

Forces at the springing of the nave vault, 23.05 m above the floor.

Why they differ

  • The building is deeper than the statics asks. Its buttresses stand at the foot of one tier of flyers: they had to give the flyers room, carry their thrust at its height and stand during building, before the vaults were closed. The kern rule asks only what the finished bay needs.
  • The check is drawn in one plane: one typical bay of the nave, the buttress breadth taken as a share of its depth, the wall as measured where known. Real buttresses vary along the church.

Ungewitter’s rules against this building

The rules of experience reported by Ungewitter and Mohrmann (1890, pp. 273–276) size the abutment of one vault span. Here they are applied to this building’s spans and heights and set against the buttresses measured on the plate.

In a basilica the nave vault is abutted through the flying buttresses by the whole system: aisles and outer buttress together. Ungewitter’s single-span rules were never meant for it, which is the point of the comparison.

Nave vault: span 10.37 m, springing at 23.09 m

RuleFilled inRule saysBuilding hasBuilding ÷ rule
Mohrmann, rule 5D = (0.222 · 10.37 m + 0.05 · 23.09 m) · 0.879 = 3.04 m3.04 m9.46 m3.11
HoffstadtD = 10.37 m / 10 + √2 · 10.37 m / 10 = 2.5 m2.5 m9.46 m3.78
Viollet-le-DucD = 7.2 m · (1 − cos(2 · 73.7 ° / 3)) = 2.49 m2.49 m9.46 m3.8
HaseD = 2.49 m + 0.15 m · 23.09 m / 4.5 m = 3.26 m3.26 m9.46 m2.9
Earlier editionsD = (7.2 m + 0.3 m) / cos(37.2 °) − 7.2 m = 2.22 m2.22 m9.46 m4.27

Building has: whole abutment system: aisles + buttress, from the nave pier’s face

Outer aisle vault: span 6.43 m, springing at 10.71 m

RuleFilled inRule saysBuilding hasBuilding ÷ rule
Mohrmann, rule 5D = 0.222 · 6.43 m + 0.05 · 10.71 m = 1.96 m1.96 m3.03 m1.54
HoffstadtD = 6.43 m / 10 + √2 · 6.43 m / 10 = 1.55 m1.55 m3.03 m1.95
Viollet-le-DucD = 4.47 m · (1 − cos(2 · 73.7 ° / 3)) = 1.55 m1.55 m3.03 m1.96
HaseD = 1.55 m + 0.15 m · 10.71 m / 4.5 m = 1.9 m1.9 m3.03 m1.59
Earlier editionsD = (4.47 m + 0.3 m) / cos(37.4 °) − 4.47 m = 1.53 m1.53 m3.03 m1.98

Building has: the buttress, from the inner face of its wall

Assumptions

  • Vault rise 2/3 of the span (a low pointed arch); springing height = vault height − rise.
  • Heavy stone; no help from the walls between the buttresses.

The modern check: Heyman’s geometric factor

The rules above size a buttress by proportion. Here the measured buttress is checked by limit analysis against an estimate of the vault’s thrust: how much shallower could it be before it overturns, as one block and once cracked?

The buttress holds the estimated thrust, but cracked its geometric factor is only 1.12.

QuantityValue
Vault thrust per bay (estimate, Table I)40 kN
Height of the thrust (springing)23.09 m
Buttress depth (measured)3.03 m
Buttress breadth (assumed: half the depth)1.52 m
Thrust it holds: block | cracked167 | 56 kN
Minimum depth: block | cracked1.88 | 2.71 m
GSF on depth: block | cracked1.61 | 1.12
Fracture height23.09 m
1890: base joint, eccentricity ÷ kern0.72

Assumptions

  • Estimates: quadripartite vault, rise 2/3 of the span, Table I (mean H₀); ashlar 24 kN/m³; the thrust acts on the inner face at the springing; buttress breadth half its depth; the masonry above the springing (pinnacles) is ignored, which is conservative.
  • In a basilica the outer buttress takes the nave vault’s thrust through the flyers; the aisle vault is left out.
  • Cracked buttress after Ochsendorf (2002) and Ochsendorf, Hernando & Huerta (2004): a straight fracture from the toe, its height from the published equations (checked against both worked examples).

How the modern check works →

Plates

Public-domain plates of this building in Dehio and von Bezold’s atlas. Open them in the Heidelberg viewer or measure them with tools/plate-digitiser.

Sources

Every work this page cites, with the plates and article revisions it uses. The plates of Dehio and von Bezold are in the public domain; Wikipedia articles serve as pointers, each fixed to its revision.

  • Wikipedia contributors. 2026. Dimension lists in German and French Wikipedia articles on Gothic cathedrals. Accessed November 21, 2026.

    Numbers only, each with its traced book citation. Prose may not be copied (CC BY-SA share-alike).

  • Wikipedia contributors. 2026. Articles on Gothic churches in the Spanish, Catalan, Italian, Czech and English Wikipedias. Accessed November 21, 2026.

    Numbers only, each with its article revision. Prose may not be copied (CC BY-SA share-alike).

  • Dehio, Georg, and Gustav von Bezold. 1887–1901. Die kirchliche Baukunst des Abendlandes: Atlas. 5 vols. Stuttgart: Cotta.

    Universitätsbibliothek Heidelberg (requested in the IIIF manifest)