Skip to content
Ungewitter

← All reference buildings

Amiens Cathedral

Amiens · Cathédrale Notre-Dame d’Amiens · Kathedrale von Amiens · Wikidata Q106934

6 measured · 3 published · 9 provisional

The canonical comparison case. The Dehio plan shows the nave without the chapels later built between its buttresses.

Facts

Main building campaign
1220–1288 provisionalfr Wikipedia, revision 241027816Main structure (fr infobox).
Plan type
Basilica, 3 vessels, with transept provisionalde Wikipedia, revision 268962783
Material
stone provisionalfr Wikipedia, revision 241027816fr: ashlar, mostly white chalk.
Nave bays
6 provisionalfr Wikipedia, revision 241027816
Choir ending
7 sides provisionalfr Wikipedia, revision 241027816fr: rond-point of seven sides; the polygon is not stated.
Towers
Crossing spire 112.70 m; north tower 66–68 m, south tower 61.70 m (fr). provisionalfr Wikipedia, revision 241027816
Vaults
Nave: quadripartite publishedDehio & von Bezold, Tafel 363, Fig. 3The crossing has a star vault of tiercerons and liernes.
East end
an ambulatory with 7 radiating chapels publishedDehio & von Bezold, Tafel 363, Fig. 3Seven radiating chapels, the axial one deep.
Towers in plan
two west towers, a crossing tower provisionalfr Wikipedia, revision 241027816Two west towers; over the crossing a timber spire (flèche).
Flying buttresses
2 tiers, one above the other publishedDehio & von Bezold, Tafel 385, Fig. 2

Dimensions

DimensionsValueConventionSource
Nave width14.52 m ± 0.2 maxis to axismeasuredDehio & von Bezold, Tafel 363, Fig. 3measured from (2739.5, 1668) to (2923, 1668) px; scale 40 m = 505.5 px

Nave piers, axis to axis.

Other figures
Aisle widths8.94 m ± 0.2 mAisle, pier axis to inner face of the wallaxis to axismeasuredDehio & von Bezold, Tafel 363, Fig. 3measured from (2626.5, 1668) to (2739.5, 1668) px; scale 40 m = 505.5 px
Other figures
Bay length7.57 m ± 0.1 maxis to axismeasuredDehio & von Bezold, Tafel 363, Fig. 3measured from (2739.5, 1477) to (2739.5, 1859.5) px; scale 40 m = 505.5 px · over 4 bays

Nave pier axes over 4 bays. fr gives the nave of six bays as 54 m (9 m a bay); that length must include more than the six bays.

Nave vault height42.3 mto the crownprovisionalde Wikipedia, revision 268962783

To the keystone; de, fr and en agree.

Aisle vault heights19.7 mto the crownprovisionalfr Wikipedia, revision 241027816

fr.

Piers2.37 m ± 0.2 mNave pier across the shafts, transverseoverallmeasuredDehio & von Bezold, Tafel 363, Fig. 3measured from (2724.5, 1668) to (2754.5, 1668) px; scale 40 m = 505.5 px
Other figures
  • 2.2 m · convention not stated provisionalde Wikipedia, revision 271917040 · after Arnold Wolff, p. 35Pier diameter after A. Wolff, Die vollkommene Kathedrale, p. 35, quoted in de “Kölner Dom”.
Buttress depths4.51 m ± 0.2 mNave buttress, outer face to inner face of the aisle walloverallmeasuredDehio & von Bezold, Tafel 363, Fig. 3measured from (2569.5, 1668) to (2626.5, 1668) px; scale 40 m = 505.5 px
Wall thicknesses0.87 m ± 0.2 mAisle wall between the buttressesoverallmeasuredDehio & von Bezold, Tafel 363, Fig. 3measured from (2615.5, 1620) to (2626.5, 1620) px; scale 40 m = 505.5 px

The design in plan

Plan of the design made from Amiens Cathedral: quadripartite nave vaults, an ambulatory with 7 radiating chapels.010 m
The Studio design made from the values on this page, drawn by the Studio’s own generators: cut masonry black, vault ribs dashed overhead. It is a design after the building, not a survey of it. The east end comes from the chevet generator (Ch. VI), which draws the church with one aisle on each side.

One bay in plan, to scale

Plan of one bay of Amiens Cathedral: nave 14.52 m between pier axes, buttress depth 4.51 m; dashed outline of Cologne Cathedral for comparison.14.52 m4.51 m010 m
Drawn from the values above: nave piers, aisles, outer wall and buttresses of one bay. Buttress breadth is schematic. The dashed outline is Cologne Cathedral at the same scale.

As a design

The measured values as a Studio design: vessels, nave width, aisle and bay ratios, nave bays, choir ending and transept, the springings (measured, or the vault crown less a rise of 2:3 over the clear span), the piers and the material. The recorded facts above, each with its source, give the vault types (the nave quadripartite), the chevet, the towers and the tiers of flyers; the building’s date sets the period of its tracery and portals. Everything else keeps the Studio’s defaults.

Measured against the 1890 statics and the modern check

The design is sized twice at its typical nave bay: by the 1890 statics (the least depth of wall and buttress that keeps the line of pressure in the kern) and by the modern check (Heyman: the least depth with a geometric factor of 2). The depth measured on the plate is then checked with the same forces by both criteria, so all three columns are judged alike.

Measured against the 1890 statics and the modern check
QuantityBuilding, measuredUngewitter 1890, staticsModern check (Heyman)
Depth of wall and buttress4.51 m measured3.29 m3.29 m
Building ÷ this depth–1.371.37
Kern rule of 1890kern keptkern left in the storm only (with wind from the left)kern left in the storm only (with wind from the left)
Geometric factor, cracked1.33 against 1: safe1.01 against 1: safe1.01 against 1: safe
Pier (1890 plan rule)2.37 m1.97 m–
Wall between the buttresses (1890 plan rule)0.87 m1.35 m–

Forces at the springing of the nave vault, 34.16 m above the floor.

Why they differ

  • The building is deeper than the statics asks. Its buttresses stand at the foot of 2 tiers of flyers: they had to give the flyers room, carry their thrust at its height and stand during building, before the vaults were closed. The kern rule asks only what the finished bay needs.
  • The check is drawn in one plane: one typical bay of the nave, the buttress breadth taken as a share of its depth, the wall as measured where known. Real buttresses vary along the church.

Ungewitter’s rules against this building

The rules of experience reported by Ungewitter and Mohrmann (1890, pp. 273–276) size the abutment of one vault span. Here they are applied to this building’s spans and heights and set against the buttresses measured on the plate.

In a basilica the nave vault is abutted through the flying buttresses by the whole system: aisles and outer buttress together. Ungewitter’s single-span rules were never meant for it, which is the point of the comparison.

Nave vault: span 12.15 m, springing at 34.2 m

RuleFilled inRule saysBuilding hasBuilding ÷ rule
Mohrmann, rule 5D = (0.222 · 12.15 m + 0.05 · 34.2 m) · 0.877 = 3.87 m3.87 m12.26 m3.17
HoffstadtD = 12.15 m / 10 + √2 · 12.15 m / 10 = 2.93 m2.93 m12.26 m4.18
Viollet-le-DucD = 8.44 m · (1 − cos(2 · 73.7 ° / 3)) = 2.92 m2.92 m12.26 m4.2
HaseD = 2.92 m + 0.15 m · 34.2 m / 4.5 m = 4.06 m4.06 m12.26 m3.02
Earlier editionsD = (8.44 m + 0.3 m) / cos(37.2 °) − 8.44 m = 2.53 m2.53 m12.26 m4.86

Building has: whole abutment system: aisles + buttress, from the nave pier’s face

Outer aisle vault: span 7.75 m, springing at 14.53 m

RuleFilled inRule saysBuilding hasBuilding ÷ rule
Mohrmann, rule 5D = 0.222 · 7.75 m + 0.05 · 14.53 m = 2.45 m2.45 m4.51 m1.84
HoffstadtD = 7.75 m / 10 + √2 · 7.75 m / 10 = 1.87 m1.87 m4.51 m2.41
Viollet-le-DucD = 5.39 m · (1 − cos(2 · 73.7 ° / 3)) = 1.86 m1.86 m4.51 m2.42
HaseD = 1.86 m + 0.15 m · 14.53 m / 4.5 m = 2.35 m2.35 m4.51 m1.92
Earlier editionsD = (5.39 m + 0.3 m) / cos(37.3 °) − 5.39 m = 1.76 m1.76 m4.51 m2.56

Building has: the buttress, from the inner face of its wall

Assumptions

  • Vault rise 2/3 of the span (a low pointed arch); springing height = vault height − rise.
  • Heavy stone; no help from the walls between the buttresses.

The modern check: Heyman’s geometric factor

The rules above size a buttress by proportion. Here the measured buttress is checked by limit analysis against an estimate of the vault’s thrust: how much shallower could it be before it overturns, as one block and once cracked?

The buttress holds the estimated thrust, but cracked its geometric factor is only 1.5.

QuantityValue
Vault thrust per bay (estimate, Table I)54 kN
Height of the thrust (springing)34.2 m
Buttress depth (measured)4.51 m
Buttress breadth (assumed: half the depth)2.26 m
Thrust it holds: block | cracked550 | 183 kN
Minimum depth: block | cracked2.08 | 3 m
GSF on depth: block | cracked2.17 | 1.5
Fracture height34.2 m
1890: base joint, eccentricity ÷ kern0.29

Assumptions

  • Estimates: quadripartite vault, rise 2/3 of the span, Table I (mean H₀); ashlar 24 kN/m³; the thrust acts on the inner face at the springing; buttress breadth half its depth; the masonry above the springing (pinnacles) is ignored, which is conservative.
  • In a basilica the outer buttress takes the nave vault’s thrust through the flyers; the aisle vault is left out.
  • Cracked buttress after Ochsendorf (2002) and Ochsendorf, Hernando & Huerta (2004): a straight fracture from the toe, its height from the published equations (checked against both worked examples).

How the modern check works →

Plates

Public-domain plates of this building in Dehio and von Bezold’s atlas. Open them in the Heidelberg viewer or measure them with tools/plate-digitiser.

Sources

Every work this page cites, with the plates and article revisions it uses. The plates of Dehio and von Bezold are in the public domain; Wikipedia articles serve as pointers, each fixed to its revision.