Zum Inhalt springen
Ungewitter
Beta

RegelModerne Statik

Der Bogen auf geneigten Strebepfeilern

modern.kinematics.arch-on-leaning-buttresses

überliefertumgesetztModerne Statik

Steht in einem mittelalterlichen Text.

Wortlaut

Neigen sich seine Strebepfeiler, wird ein Bogen auseinandergezogen: sein Schub steigt, während die Tragkraft der Pfeiler sinkt. Eines von zwei Dingen beendet das. Sind die Pfeiler stark, erreicht der Bogen die größte Spreizung, der er folgen kann, und stürzt durch seinen eigenen Mechanismus ein, die Pfeiler unversehrt (Versagen bei starken Pfeilern); das ist der übliche Fall bei dünnen Bögen. Ist der Bogen dick, kann sein Schub die sinkende Tragkraft zuerst überholen: der Pfeiler gibt nach, dreht sich weiter, und der Bogen fällt (Versagen bei schwachen Pfeilern). In beiden Fällen bleibt der Pfeiler meist stehen, vom Schub befreit. Hohe, schlanke Pfeiler heben den Kämpfer, sodass eine kleine Neigung die Spannweite stärker weitet und ihre Tragkraft schneller sinkt: solche Bögen können schon bei weniger als 1° Neigung einstürzen.

Formel

ΔL=hϕ per leaning buttress,collapse at the least ϕ with Harch(ΔL)>Hϕ or ΔL>ΔLmax⁡

Kennwerte

validation_goa.arch_R_m
5
validation_goa.t_over_R
0,1
validation_goa.half_angle_deg
60
validation_goa.leaning
south wall only
validation_goa.thrust_at_0_4_deg_kN
41
validation_goa.collapse_lean_deg
slightly more than 2.0
validation_goa.mode
weak-buttress
validation_goa.thrust_at_collapse_kN
52
validation_goa.crown_drop_m
0,4
validation_goa.thin_arch.t_over_R
0,05
validation_goa.thin_arch.collapse_lean_deg
1,1
validation_goa.thin_arch.mode
strong-buttress
validation_goa.source_page
131–134
engine_goa
2.01°, weak-buttress, 52.3 kN, crown down 0.41 m, 41.5 kN at 0.4°; t/R = 0.05: 1.09°, strong-buttress
case_a_fig_7_3
collapse leans 0.8°, 2.1°, 3.4°, 4.75° for t/R 0.05–0.20 (read off the figure); engine 0.76°, 2.06°, 3.36°, 4.71°
threshold_fig_7_5
Reproduced by ArchLean’s own stepping (archOnLeaningButtresses with listing: true): the first weak-buttress failure at t/R between 0.155 and 0.1575 for Case A (printed 0.156) and between 0.103 and 0.1045 for Case B (printed 0.104). Two features of the listing decide it (pp. 166–169): in each step the buttress is checked before the arch, and right after a hinge move the thrust is computed with the crown segment’s centroid unrotated (XM1 = X_O + C1 sin(p/2), where the main loop has sin(p/2 − φ)), which understates it, so the arch survives the jump and in the next step the overshooting thrust is charged to the buttress. With the centroid rotated the listing’s thresholds are 0.171 and 0.107.
threshold_engine
The engine follows the converged mechanism and, where a hinge jump overshoots both limits at once, lets the weaker part give way: Case B changes mode between 0.1045 and 0.106, Case A between 0.165 and 0.1675. Above that the arch’s own collapse and the buttress’s giving way fall within one hinge step of each other, and with 1° voussoirs the mode alternates with t/R (for Case A strong again at 0.1975–0.2, 0.21–0.215, …) while the lean at collapse runs on smoothly (about 0.068° per 0.0025 of t/R). The threshold thickness is therefore ill-conditioned; the collapse lean is not. Until wave 6 the engine charged every simultaneous overshoot to the arch, which put the thresholds at about 0.117 (B) and above 0.2 (A).

Aus heutiger Sicht

Nachgelesen in der Dissertation, §7.3 und §8.2, mit dem Listing von ArchLean (Anhang A.3), das das Programm auch Anweisung für Anweisung nachrechnen kann: der spreizende Bogen aus Kapitel 5 auf dem gerissenen rechteckigen Pfeiler der Kapitel 3–4, dessen Tragkraft mit der Neigung nach Gl. 4.9 sinkt; beide Pfeiler geneigt (oder, wie in Goa, nur einer: dann wächst die Spannweite um h·φ statt um 2h·φ).

Quellen

  • Ochsendorf 2002, S. 112–121, 129–134, 164–170, Fig. 7.2–7.6, 8.1–8.3, App. A.3

Umgesetzt in

@ungewitter/statics#archOnLeaningButtresses

Werkzeuge zu diesem Bereich

Begriffe